AUCTION CLOSED...

FEG FEG P9R 9mm


Meet the Seller
Location (State):
North Carolina (NC)
North Carolina


Member For:
9 Years 8 Months
AUCTION CLOSED
WINNER: s********l
HIGH BID: $163.00
Share this deal:
Mail this auction to a friend..
Put this on my Watch List.
Payment Method:
(NOT SPECIFIED)
Shipping Fee: (NOT SPECIFIED)

Auction: 8504850

Auction Type:
Basic
NRA Grade:
Good
Current High Bidder:
s********l
History:
36 Bids ($0.01 starting bid)
(Log In to view Bid History)
Bid Increment:
$1.00
Auction Start:
(February 28, 2008 07:22:47 PT)
Auction Ended:
(March 13, 2008 07:22:47 PT)

Buyer Tip: If you're the High Bidder in an auction when it closes, don't assume you're the final High Bidder. Someone could outbid you in the final seconds of the auction if your Max Bid isn't high enough. You're not the high Bidder until you've been notified by email that you are. All Auctions are conducted in Pacific Time.


Related Searches:   (FEG Auction)  (FEG for Sale)  (FEG Accessories for Sale)  (Handguns for Sale)  (Pistols for Sale)  (Guns for Sale)  (Used Guns for Sale)  (Sell FEG)  (Sell a Handgun)  (Sell FEG Pistol)  (Sell a Pistol) 
Seller's Description

Guns For Sale - FEG -- FEG P9R 9mm

FEG P9R in 9mm, pistol looks good with only a couple of very small scratches in the finish, gotta look hard to find them.Grips are fine with no chips,or cracks.Only problem with this gun is someone turned the end of the barrell down about an inch back from the muzzell end in an attempt to put a comp on. Other than that it looks nearly new, but it will take a new barrell to fix. Comes with two 15 round mags. No box or manual. Shipping to your FFL dealer is $20.00

Payment and Shipping Instructions:
Make sure this item is legal in your area. Must ship to a valid FFL and will require a signed copy+ payment before shipment.Know your states laws to include magazine capacity restrictions before you bid. Postal money order preferred, all personal checks will be held till they clear. $20.00 shipping.
Payment Methods:

(NOT SPECIFIED)

Ships Using:



Hide Pictures   If you've got a slow modem, give this a try (must have cookies enabled) ...

FEG - FEG P9R 9mm - Picture 1
FEG - FEG P9R 9mm - Picture 2
FEG - FEG P9R 9mm - Picture 3
FEG - FEG P9R 9mm - Picture 4
FEG - FEG P9R 9mm - Picture 5
FEG - FEG P9R 9mm - Picture 6
FEG - FEG P9R 9mm - Picture 7
FEG - FEG P9R 9mm - Picture 8
FEG - FEG P9R 9mm - Picture 9


This Auction has been viewed 1840 times.

Buyer Tip: Seller assumes all responsibility for listing this item. If you have any questions regarding this item, you should contact the Seller before bidding. You can contact the seller by clicking on the seller's nickname. The Seller is required to give the Buyer a minimum of three days to inspect any firearm sold through GunAuction.com. See the GunAuction.com Terms and Conditions for details.
Questions for Users
(Public)   
    Q:  will it still shot thanks 02/28/2008
        A:  While there is no doubt it will still shoot, fire, function, the whole nine yards, the wisdom of doing so is questionable. With no bearing surface at the front of the slide and barrell, the only thing you would be able to hit would be the ground. Also with the barrell tilted down in front from being turned, it most likely changes the relationship of the locking lugs at the back. I am not recomending anyone shoot this firearm without replacing the barrell. The rest of the gun is like new, BUT the barrell MUST be replaced. Kurt 02/29/2008
 
(Public)   
    Q:  so all this gun needs to be correct is the barrel no bushing or anything thanks much for the time 03/03/2008
        A:  That is correct. This pistol does not use a bushing. A new barrel will put it back in 100% working order. I just found the other magazine and will include it for whoever wins the auction, for a total of two 15 round mags. Thanks for the inquiry. Kurt 03/03/2008
 
(Public)   
    Q:  Sir, Can you cock back the slide and show the barrell tip in a photo. Thank you. 03/11/2008
        A:  Hope these photos help. The barrel was evidently centered and turned on a lathe. Kurt 03/11/2008